Bemutatótermünk működését - más irányú elfoglaltságaink következtében - felfüggesztettük.

Megkeresését egyéb elérhetőségeinken várjuk!

Info: +36-30/6701767 (H-P.: 8-18 óráig!)

Plinius SB 301 high end végerősítő / végfok

A Plinius közel 40 év tapasztalattal rendelkezik High End erősítők fejlesztésében, amit az erősítők által nyert számos nívós elismerés is tükröz. A Plinius SB 301 high end végerősítő / végfok valóban egy csúcskategóriás sztereó végfok, ami kifinomult hangjának és gyönyörű vonalvezetésének köszönhetően mindenképpen kerüljön fel a bakancslistára high end végerősítő vásárlásakor.

Általános információk:

A megrendelés menetéről érdeklődjön!
A megrendelés menetéről érdeklődjön!
Termékismertető - Specifikáció

Plinius SB 301 high end végerősítő / végfok tulajdonságai:

Plinius végfokok

SB 301 Power Amplifier

For the technically minded the SB-301 is a Class AB two channel amplifier that delivers over 300 watts per channel at 8 ohms.

For the not so technically minded that means it's a really good stable amplifier unit when the speakers demand a lot of power to drive bass without distortion or treble with detail and finesse and it will cope with inefficient speakers. The standing temperature is lower than that encountered in Class A series designs because it's a Class AB design.

It occupies a niche in audio systems for the person that really loves big dynamic sound like movies, orchestral pieces and of course playing music loud!

The physical construction of the SB-301 is based on the SA series designs so it has the same distinctive aesthetic as the Class A products and indeed much of the electronics topology is derived from that Class A history

This amplifier delivers all the dynamics, finesse and transparency that Plinius is renowned for. Like all Plinius products it is very reliable and will rise to the challenge of difficult operating conditions time and time again.


310 watts RMS per channel into 8 ohms.
470 watts RMS per channel into 4 ohms.
Both channels driven from 20Hz to 20kHz at less than 0.2% total harmonic distortion


20Hz to 20kHz ±0.2dB
-3dB at 70kHz


Typically <0.05% THD at rated power
0.1% THD and IM worst case prior to clipping


100A short duration peak per channel
Fuse protected


Typically 5µs


+0° at 20Hz and -14° 20kHz


100dB below rated output 20Hz to 20kHz, A-weighted


47k ohms


RCA Inputs: 32dB
Balanced Inputs: 38dB


1.6A (370W) Class AB Idle
0.2A (46W) Standby


Height: 220mm (8 3/4 ")
Width: 500mm (19 3/4")
Depth: 455mm (18")
Weight: 38kg (83lb)


Amplifier Configuration Selector (ACS) switch
The rear panel ACS switch allows for the amplifier to be configured for Stereo RCA or XLR modes.


Remote Trigger Input
When connected to a preamplifier trigger output, the amplifier will switch out of Standby and be ready for use when the preamplifier is taken out of standby.


Ground Lift Switch
This allows for the signal ground to be isolated from the main chassis earth. This can assist in resolving unwanted ground loops or hum due to duplicate ground paths in some systems.


WBT and Neutrik Connectors
High quality WBT RCA and Neutrik XLR input connectors are fitted along with WBT output speaker terminals to ensure a low distortion interface between your cables and the amplifier.


Auricap Capacitors
Audience AV supply the Auricap XO capacitors used in several key areas of the circuit.


Siltech Wiring
Siltech premium 'G7' silver/gold wire provides a perfect connection between components to give clear, fast and detailed presentation of the music signal.


Aluminium Construction
The aluminium construction provides a rigid non-magnetic housing to eliminate unwanted magnetic fields that can interfere with the sensitive audio signals.